Drivers searching for a front lip for W118 / C118 CLA45 with AMG CLA45 sport bumper can use this Mercedes-Benz W118 / C118 CLA45 FDGT Carbon Front Lip guide to compare fitment, construction, mounting method and ownership requirements for 2027.
Mercedes-Benz W118 / C118 CLA45 FDGT Carbon Front Lip overview
A front lip extends the visual lower edge of the bumper and can make the nose appear lower and wider. The important design points are the centre projection, the transition into the bumper corners and even clearance across the full width.
The C118 CLA Coupe and X118 Shooting Brake share a design language but differ around the roof and rear bodywork. CLA45, AMG Line and standard bumpers can also require different aerodynamic pieces.
The FDGT designation identifies the visual variant of this product. It should be compared directly with the regular FD version, particularly around projection, corner treatment and the way it connects with adjacent bumper or sill lines.
Specifications and Mercedes-Benz application
- Vehicle application: W118 / C118 CLA45 with AMG CLA45 sport bumper
- Model years: 2019-now
- Product type: Front Lip
- Style: FDGT
- Material: Dry carbon / Vacuum Infusion
- Installation: Add on / drilling screw & bolt
Compatibility and fitment for W118 / C118 CLA45 with AMG CLA45 sport bumper
Compare the underside screw positions, outer corner shape and the profile around any factory splitters or cooling openings. The body style and factory exterior package should match the product photographs at every mounting edge.
Before ordering for a vehicle from 2019-now, compare close photographs of both mounting edges. Badge names often continue across styling revisions, while the bumper or boot-lid geometry changes underneath.
Installation requirements
The stated method is Add on / drilling screw & bolt. Mark and test-fit every mounting point before drilling, protect exposed holes against corrosion where applicable and tighten fasteners evenly rather than pulling an inaccurate part into position.
Front lips are exposed to kerbs, ramps and road debris, so secure fastening and adequate ground clearance are more important than appearance alone. Use masking tape reference marks during the dry fit so the final position can be reproduced after cleaning the mounting surface.
Material, finish and delivery inspection
The listing identifies Dry carbon / Vacuum Infusion construction. For this type of composite part, low weight is useful, but the practical quality checks are consistent weave direction, an even clear coat, clean edges and mounting surfaces that are not distorted.
Review the supplied fasteners separately from the component. Generic screws or tape may not be appropriate for every mounting surface, and a professional installer may specify different hardware.
Price, availability and ordering in 2027
DAS Motor can help confirm current price and availability for the exact Mercedes-Benz application. Request a fitment check with the chassis code, model year, body style and clear photographs of the mounting area before purchase.
Before paint protection film or ceramic coating is applied, complete a full trial fit. This avoids paying for surface finishing on a component that later requires trimming, drilling or replacement.
Inspect the lower surface periodically for impact marks, loose fasteners and clear-coat damage. After the first week, recheck alignment and every accessible fixing because adhesive settling and vibration can reveal an edge that was not fully supported.
Mercedes part pre-order checklist
- Compare product and vehicle photographs at the same angle.
- Confirm year range against the build date.
- Identify any previous bumper or body repair.
- Check whether factory clips can be reused.
- Budget for preparation and installation materials.
- Verify the seller's policy before drilling or bonding.
Mercedes-Benz W118 / C118 CLA45 FDGT Carbon Front Lip FAQ
Does this front lip fit every W118 / C118 CLA45 with AMG CLA45 sport bumper?
No. Confirm the chassis code, body style, production date, bumper package and mounting geometry. A shared sales name does not guarantee identical exterior panels.
What should be checked before ordering in 2027?
Verify current stock, price, delivery terms, included hardware, material specification and the seller's fitment evidence for the exact VIN or vehicle configuration.
Is professional installation recommended?
Yes. A specialist should dry-fit the component, check symmetry and clearance, and confirm the correct adhesive or mechanical fasteners before any permanent modification.
Related Mercedes-Benz styling guides
- Mercedes-Benz W118 / C118 CLA45 FD Carbon Front Lip
- Mercedes-Benz W118 / C118 CLA FDGT Carbon Front Lip
- Mercedes-Benz W118 / C118 CLA FD Carbon Front Lip
- Mercedes-Benz W118 / C118 CLA Shooting Brake FD style Carbon Trunk Spoiler
Browse the complete Popular Mercedes Products cluster for Mercedes-Benz carbon parts, exterior accessories, fitment guides and 2027 buying references.
Product specification and photography reference: original product listing. Availability and specifications may change; confirm current details before ordering.
