The Mercedes-Benz W213 facelift Sedan FD Carbon Rear bumper Splitter is a model-specific Mercedes styling part for W213 facelift Sedan with AMG sport bumper. The sections below explain the stated specification, practical fitment checks, installation planning and buying questions that matter in 2027.
Mercedes-Benz W213 facelift Sedan FD Carbon Rear bumper Splitter overview
A rear bumper splitter adds a defined lower edge around the diffuser area without replacing the complete bumper insert. The piece should follow the bumper width, exhaust layout and outer corner transitions with consistent projection.
Facelift W213 sedan bodywork differs from the earlier version around the bumpers, grille and trim details. A part described for the facelift car should not be assumed to fit a pre-facelift E-Class without a direct comparison.
The stated FD style defines this particular shape within the supplier's range. Products carrying the same general name can still differ in projection, number of pieces and mounting geometry.
Specifications and Mercedes-Benz application
- Vehicle application: W213 facelift Sedan with AMG sport bumper
- Model years: 2020-now
- Product type: Rear Bumper Splitter
- Style: FD
- Material: Dry carbon / Vacuum Infusion
- Installation: Add on / 3M tape adhering
Compatibility and fitment for W213 facelift Sedan with AMG sport bumper
Check the bumper version, exhaust outlets and any factory trim that occupies the same mounting line. The sedan application should be checked against the boot lid and bumper shape rather than an estate, coupe or pre-facelift body.
Treat the 2020-now model-year statement as supplier guidance. A VIN check and a direct visual comparison are still necessary where AMG, AMG Line and standard exterior parts overlap.
Installation requirements
The stated method is Add on / 3M tape adhering. Adhesive installation depends on temperature, surface preparation and uninterrupted contact pressure; polish, wax and silicone dressing must be removed from the bonding area.
Trial assembly helps identify whether factory screws can be reused or whether additional mounting points are necessary. Use masking tape reference marks during the dry fit so the final position can be reproduced after cleaning the mounting surface.
Material, finish and delivery inspection
The listing identifies Dry carbon / Vacuum Infusion construction. For this type of composite part, low weight is useful, but the practical quality checks are consistent weave direction, an even clear coat, clean edges and mounting surfaces that are not distorted.
Place the uninstalled part on a padded surface and compare left and right sides. Uneven curvature, twisted mounting flanges or blocked holes should be resolved before the vehicle is dismantled.
Price, availability and ordering in 2027
DAS Motor can help confirm current price and availability for the exact Mercedes-Benz application. Request a fitment check with the chassis code, model year, body style and clear photographs of the mounting area before purchase.
Before paint protection film or ceramic coating is applied, complete a full trial fit. This avoids paying for surface finishing on a component that later requires trimming, drilling or replacement.
Monitor the lowest edge for contact damage and recheck fixings after the first heat cycles around the exhaust. After the first week, recheck alignment and every accessible fixing because adhesive settling and vibration can reveal an edge that was not fully supported.
Mercedes part pre-order checklist
- Confirm left-hand and right-hand symmetry.
- Measure the principal mounting surface.
- Check cameras, radar and parking sensors.
- Review exhaust and tow-equipment clearance.
- Inspect the delivery before dismantling the car.
- Retain packaging until fitment is established.
Mercedes-Benz W213 facelift Sedan FD Carbon Rear bumper Splitter FAQ
Does this rear bumper splitter fit every W213 facelift Sedan with AMG sport bumper?
No. Confirm the chassis code, body style, production date, bumper package and mounting geometry. A shared sales name does not guarantee identical exterior panels.
What should be checked before ordering in 2027?
Verify current stock, price, delivery terms, included hardware, material specification and the seller's fitment evidence for the exact VIN or vehicle configuration.
Is professional installation recommended?
Yes. A specialist should dry-fit the component, check symmetry and clearance, and confirm the correct adhesive or mechanical fasteners before any permanent modification.
Related Mercedes-Benz styling guides
- Mercedes-Benz W213 facelift Sedan FD Front Grille
- Mercedes-Benz W213 facelift Sedan FD Carbon Rear Diffuser
- Mercedes-Benz W213 facelift Sedan FD Carbon Front Lip
- Mercedes-Benz W213 facelift Sedan FD Carbon Side Skirt Splitter
Browse the complete Popular Mercedes Products cluster for Mercedes-Benz carbon parts, exterior accessories, fitment guides and 2027 buying references.
Product specification and photography reference: original product listing. Availability and specifications may change; confirm current details before ordering.
